Camera Flywoo HDZero Whoop Lite Bundle

The HDZero Whoop Lite Bundle is an ultra-lightweight, high-definition digital FPV transmission system explicitly engineered to transform 1S, 2S, and 3S micro whoops and toothpick platforms into the digital HD ecosystem. Achieving a breakthrough collective component footprint, the bundle couples the ultra-miniaturized HDZero Nano Lite camera module (weighing just 1.5 grams) with the Whoop Lite video transmitter (VTX) mainboard (weighing 4.5 grams with its linear dipole element). Delivering fixed-rate, low-latency 720p digital video processing at 60fps, this integrated system allows micro aircraft to bypass heavy analog limitations while preserving sub-250g weight classes and agile power-to-weight flight dynamics.

Features

Ultra-Miniaturized Micro Component Footprint: Delivers a complete, high-definition digital video setup weighing a collective ~7 grams including the dipole antenna, optimized for protecting micro whoop throttle performance.

High-Sensitivity 1/2-Inch Digital Sensor: Outfitted with a custom 0.5-inch CMOS core driving a high 10650 mV/Lux-sec sensitivity threshold to maintain clean tracking visibility under dark, unpredictable indoor and low-light ambient conditions.

Four-Lane MIPI CSI Video Pipeline: Utilizes a dedicated 20-pin, 0.30mm pitch internal MIPI data connection matrix to feed high-fidelity YUV422 digital data from the camera module down to the transmitter core without signal compression.

Adjustable Power and SmartAudio Support: Features a variable output transmitter supporting clear close-range 25mW racing profiles up to 200mW for structural obstacle penetration, adjustable directly via your radio transmitter sticks through SmartAudio telemetry.

Standardized Board Mounting Pattern: Designed with a industry-standard 25.5mm × 25.2mm soft-mount layout, providing native drop-in stack alignment on top of standard AIO flight controllers.

Broad Micro Voltage Input Corridor: Built with an onboard regulation rail that safely accepts direct power from 1S to 3S flight battery configurations, preventing low-battery voltage sag blackouts during high-throttle maneuvers.

Specifications

Brand: HDZero / RunCam

Model Name: Whoop Lite High-Definition Digital FPV System Bundle

HDZero Whoop Lite VTX Specifications

Physical Component Mounting Template: 25.5 mm × 25.2 mm (Soft-Dampened M2 Layout)

Total Hardware Dimensions: 32.4 mm × 32.5 mm (Inner structural framing measures 29.0 mm × 29.0 mm)

Primary Camera Input Connector: 20-Pin MIPI Socket Interface (0.30 mm Pin Pitch)

Digital Video Feed Format: 4-Lane MIPI CSI Protocol (YUV422 Stream Matrix)

Native Video Transmission Quality: 1280 × 720 High-Definition @ 60 fps

Selectable Output RF Power Profiles: 25 mW / 200 mW Dual-Tier Selection

Operating RF Frequency Band: 5.8 GHz Wireless Band

Telemetry Protocol Interface: SmartAudio Configuration Control Supported

Primary Power Allocation Demand: 1000 mA Peak Draw @ DC 5.0 V

Input Voltage Operating Windows: 1S – 3S LiPo Battery Base Safe Range

Physical RF Antenna Interface: U.FL Core Terminal Socket

Physical Profile Thickness: 4.0 mm

Physical Board Net Mass: 4.5 g (Including loose 0.4 g linear dipole antenna element)

HDZero Nano Lite Camera Specifications

Image Sensor Hardware: 1/2-Inch (0.5-inch) High-Sensitivity CMOS Sensor Core

Sensor Light-Sensing Threshold: 10650 mV/Lux-sec

Digital Video Transmission Target: 720p60 High-Definition Output

Shutter Mechanism Profile: Rolling Shutter Matrix

Primary Input Power Demand: DC 3.3 V Regulated Input (Sourced from Whoop Lite VTX Only)

Average Sensor Power Consumption Draw: 0.5 W

Physical Component Footprint: 14 mm × 16 mm × 11 mm (Nano Standard Form Factor)

Physical Structural Net Mass: 1.45 g – 1.5 g (Camera Module Only)

Optical Field of View (FOV) Configurations

16:9 Aspect Ratio Display: 122° Diagonal (D) / 108° Horizontal (H) / 65° Vertical (V)

4:3 Aspect Ratio Display: 130° Diagonal (D) / 108° Horizontal (H) / 84° Vertical (V)

Operational Instructions

Mechanical Stack Integration: Mount the provided soft-dampening rubber grommets into the 25.5mm M2 mounting holes of the Whoop Lite VTX board. Align the board on top of your flight controller's plastic standoffs, making sure the components do not pinch any surface-mount parts.

Digital MIPI Cable Interlocking: Locate the micro-thin 20-pin, 0.30mm pitch MIPI ribbon cable included in the bundle. Carefully align the ribbon lead flat pins and slide the cable head straight into the rear locking socket of the Nano Lite camera, then lock the matching connector socket on the VTX board.

Power Wire Mapping Schema: Solder the included direct wiring connection harness to your flight controller mainboard pads. Connect the Red wire to a positive power pad (ensuring it matches your 1S-3S power distribution layout), Black wire to a Ground (GND) pad, and the remaining SmartAudio/UART lines to a free flight controller TX pad. Connect the harness plug to the VTX power port.

Antenna and Camera Alignment: Click the provided 5.8G linear dipole antenna onto the VTX board's U.FL RF terminal socket, ensuring it snaps securely into place. Position the 14mm Nano Lite camera inside your canopy shell, lock it in using micro screws, and adjust your vertical flight angle.

System Binding and Configuration: Turn on your HDZero FPV Goggles or VRX module and connect a flight pack to the drone. Verify the 720p HD video initializes instantly. Enter the Betaflight Configurator Peripheral tab, configure the chosen UART port to "Peripheral: MSP", and activate the HDZero VTX table to enable remote SmartAudio channel tuning.

Notes

Strict MIPI Interface Ribbon Safety: The ultra-fine 20-pin digital ribbon cable transmits high-frequency processing streams. Do not crease, make sharp 90-degree folds, or twist the ribbon line during canopy mounting, as microscopic trace fracturing will cause immediate digital video blackouts, severe data freezing, or permanent connection failure.

Strict 3.3V Camera Power Input Limit: The HDZero Nano Lite camera module is strictly engineered to draw its power from the regulated 3.3V DC power rail provided through the MIPI socket of the Whoop Lite VTX. Never connect the camera power lines directly to standard 5V pads, 9V pads, or external raw battery rails, as bypassing the input limits will cause immediate, unrecoverable sensor component burnout.

RF Transmission Safety Policy: Never power on the Whoop Lite VTX module via a flight battery without the 5.8G linear dipole antenna clicked tightly onto the U.FL connector socket. Operating the VTX without an antenna prevents the transmitter from dissipating its RF energy, causing rapid heat buildup and permanent destruction of the primary amplification circuits.

Thermal Heat Management Warning: High-definition digital video transmitters generate rapid localized heat build-up while sitting idle on the bench without cross-flow ventilation. Avoid leaving the battery connected on the ground for extended setup periods; calibrate settings quickly or utilize a portable field fan to prevent automated thermal shutdown or component degradation.

Package

1 x HDZero Nano Lite Digital HD FPV Flight Camera Module

1 x HDZero Whoop Lite 5.8G Digital Video Transmitter Board

1 x Dedicated Multi-Wire Direct Power Connection Harness Set

1 x High-Flexibility 5.8G Linear Dipole Antenna Element

1 x Technical Hardware Standoff Mounting Fastener Pack

1 x Custom 20-Pin Micro MIPI Digital Interface Ribbon Cable

4 x Rubber Shock-Absorbing Soft Mount Dampers

2 x Nylon Cable Zip-Ties