BEC Power Cable for GOCam G3

The GEPRC BEC Adapter for GOCam PM G3 is a high-efficiency, ultra-lightweight power regulation step-down module explicitly engineered for FPV cinematic drone pilots looking to strip weight from their aircraft. Designed to completely replace the camera's original heavy internal lithium battery, this adapter taps directly into the quadcopter's primary flight battery to supply a continuous, regulated voltage stream. Utilizing advanced multi-layer circuit insulation and reinforced mechanical joint welds, it delivers clean, noise-free power processing to the camera sensor within an incredibly small physical footprint weighing only 5.5 grams.

Features

Direct Airborne Power Stripping: Eliminates the need for isolated action camera batteries, allowing pilots to shave critical grams off the camera assembly to maximize aircraft flight efficiency and agility.

Press-Welded Structural Integrity: Onboard Printed Circuit Board (PCB) trace positions utilize an advanced industrial press-welding technique, creating ultra-robust, high-vibration-resistant core joints that resist pulling or cracking under severe flight stresses.

Heavy-Duty Thermal Wrap Shielding: Surrounded by a specialized thick polyolefin heat-shrink tube encasing the entire converter layout, providing rugged defense against moisture ingress, structural abrasion, and short-circuits.

True Plug-and-Play Integration: Custom-terminated to provide an absolute out-of-the-box configuration that links with native GOCam electronics without requiring manual soldering or custom wiring adapters.

High-Throughput Output Delivery: Features a highly stable 5V/3A switching regulator network engineered to manage continuous data logging and heavy UHD processing demands without localized voltage drops.

Specifications

Brand: GEPRC (or equivalent premium framework)

Model Name: BEC Power Supply Adapter Matrix

Target Camera Compatibility: GOCam PM G3 (and matching micro-cam architectures)

Input Operating Voltage Corridor: 4S – 6S Multicell Lithium Polymer (LiPo) Series Airframe Rails

Regulated Output Power Performance: DC 5.0 V / 3.0 A Continuous Pipeline

Primary Input Interface Interface: XH2.54 Connector Block (Standard balance lead footprint)

Primary Hardware Output Interface: PH1.0 Male Terminal Head

Total Assembly End-to-End Length: 110 mm

Physical Structural Net Mass: 5.5 g

Operational Instructions

Input Power Interface Connection: Plug the high-conductivity XH2.54 input connector directly into the matching balance lead plug of your drone's 4S to 6S LiPo flight battery or an integrated power distribution board line.

Camera Interface Alignment: Guide the fine PH1.0 male output connector terminal toward the dedicated power receiver port on the GOCam PM G3 camera housing, noting correct pin slot registration.

Lock Execution Check: Press the connector firmly in place until fully seated. Turn on the drone's primary flight system; the camera will automatically receive regulated 5V power, bypassing standard battery diagnostic checks.

Safe Line Disconnection: To disassemble, carefully grasp the hard molded terminal hoods of the plugs to slide them out of their sockets. Never yank or apply tension to the flexible 110mm center silicone wire lines.

Notes

Strict Input Voltage Limits: This BEC adapter is strictly engineered to handle high-voltage inputs ranging from 4S to 6S LiPo power grids. Do not attempt to link this line to lower-tier 2S–3S setups (which will fail to initialize the regulator) or excessive over-voltage configurations beyond 6S, as this will induce immediate terminal component burnout.

Polarity Alignment Safety Check: Always ensure the balance plug alignment completely matches the ground and positive pin distribution layouts of your battery pack before locking the connection down. Reversing terminal orientation bypasses structural protections and can permanently toast both the adapter and the connected camera core.

Continuous Cooling Airflow Requirement: Like all compact voltage step-down regulators, the internal PCB generates moderate localized heat during heavy 3A current transformation. Avoid burying the heat-shrunk circuit module deep inside insulated foam voids or near massive heat sources like high-power Video Transmitters (VTX) without adequate cross-flow ventilation.

Package

1 x GEPRC BEC Adapter for GOCam PM G3 Camera Power Delivery System

1 x Factory Technical Reference Sheet