Flywoo RunCam HDZero Micro Camera V2

The RunCam HDZero Micro Camera V2 is a high-performance, high-definition digital FPV flight camera explicitly engineered for the HDZero video transmitter ecosystem. Utilizing an oversized, high-sensitivity 1/2-inch CMOS sensor, this micro-sized digital camera outputs a fixed-rate, low-latency 720p digital stream at 60fps. Housed within a standardized 19mm micro chassis framework weighing 8.5 grams, it combines extreme starlight-level light processing with fully adjustable sensor parameters, providing pilots with an exceptional high-definition tracking solution for both competitive daytime racing and unpredictable low-light environments.

Features

Optimized HDZero Ecosystem Alignment: Custom-engineered for seamless digital hardware integration with HDZero and RunCam digital video transmission modules.

Massive 1/2-Inch High-Sensitivity Sensor: Outfitted with an oversized 1/2-inch CMOS core boasting an impressive 10650 mV/Lux-sec sensitivity rating, yielding crisp visual capture with minimal noise grain under low-light conditions.

High-Definition Fluid 60fps Pipeline: Transmits a continuous 720p digital transmission stream, eliminating the frame ghosting, screen tearing, and static interference lines common to analog systems.

Standardized Micro Chassis Architecture: Enclosed in a standard 19mm × 19mm footprint that fits natively into most consumer and commercial drone frames, with an included backplate for clean installation.

Adjustable Aspect Ratio Profiles: Incorporates an internal menu engine that allows pilots to toggle between a native 4:3 racing layout and a widescreen 16:9 cinematic view to match any FPV goggle configuration.

Customizable Parameter Matrix: Features internal software settings allowing pilots to customize image properties such as brightness, contrast, and saturation, alongside horizontal/vertical image flipping functions to match any custom mounting geometry.

Specifications

Brand: RunCam / HDZero

Model Name: HDZero Micro Camera V2 HD Digital FPV Camera Matrix

Image Sensor Hardware: 1/2-Inch High-Sensitivity CMOS Sensor Core

Digital Video Resolution Target: 720p High-Definition @ 60 fps

Sensor Sensitivity Rating: 10650 mV/Lux-Sec

Selectable Aspect Ratio Profiles: 4:3 Standard / 16:9 Widescreen (Switchable)

Integrated Image Controls: Brightness, Contrast, Saturation, Horizontal Mirroring, Vertical Flipping

Shutter Mechanism Profile: Rolling Shutter Matrix

Primary Input Power Demand: DC 3.3 V Regulated Rail

Average Power Consumption Draw: 0.5 W

Physical Component Footprint: 19.0 mm × 19.0 mm × 21.0 mm (Micro Size Standard)

Physical Structural Net Mass: 8.5 g (Camera Unit Only)

Environmental Operating Boundaries: 0°C to +40°C (32°F to 104°F)

Operational Instructions

Mechanical Mounting Integration: Place the 19mm camera housing between the structural side plates of your drone frame canopy. Secure the module using the included mounting hardware kit, adjusting the vertical tilt angle to match your forward flight velocity before final torque application.

Digital MIPI Ribbon Interlocking: Obtain a compatible high-shielding HDZero MIPI camera ribbon cable (sold separately). Guide the cable ribbon terminal head straight down into the camera's rear MIPI socket interface until it securely seats, ensuring the delicate contact pins are completely aligned.

VTX Connection Interlocking: Route the opposite end of the MIPI cable into your HDZero video transmitter module. Lower any structural locking bars or clamp plates to ensure the high-frequency digital connection lines do not vibrate loose under high-G impacts.

Aspect Ratio System Calibration: Power up your HDZero FPV Goggles or VRX monitor module and link a flight pack to the drone. Navigate into the VTX on-screen display (OSD) settings menu to toggle between the native 4:3 frame profile or the widescreen 16:9 configuration depending on your viewing hardware preferences.

Pre-Flight Video Validation: Confirm that the digital 720p video stream initializes instantly inside your viewing goggles, and check that exposure levels and low-light tracking curves adjust smoothly when rotating from dark ground shadows into bright overhead ambient lights.

Notes

MIPI Ribbon Cable Omission: This digital camera package ships from the factory without a MIPI ribbon connection cable. You must purchase a standalone HDZero-compatible MIPI cable tailored to the specific length required by your airframe to complete the video transmission path.

Strict 3.3V Input Limit Policy: This digital micro camera is engineered to run exclusively from a highly stable, regulated 3.3V DC power bus provided via the HDZero VTX unit. Never attempt to wire this camera module directly to a standard 5V pad or raw multi-S battery power lines, as bypassing input constraints will instantly cause unrecoverable digital processor burnout.

Delicate Digital Component Care: The micro-thin digital MIPI ribbon cable transmits extremely high-frequency data tracks. Avoid pinching, making sharp 90-degree creases, or routing the cable lines across raw carbon fiber frame edges, as microscopic trace fracturing will cause immediate digital video blackouts, erratic data freezing, or permanent connection failure.

Avoid Mechanical Over-Tightening: When locking the micro mounting screws into the camera's metal framework, stop turning immediately once firm resistance is felt. Excessive torque can strip out the internal threads of the casing, resulting in severe flight vibration blurring and erratic footage.

Package

1 x RunCam HDZero Micro Camera V2 Digital HD FPV Flight Camera Module

1 x Structural Mechanical Hardware Mounting Fastener Kit

1 x Protective Interface Rear Casing Backplate

1 x High-Fidelity Optical Lens Protective Guard Cap