Flywoo Runcam Link Wasp Camera w/ 120mm cable

The RunCam Link Wasp is a high-performance, high-definition digital FPV flight camera module engineered for seamless integration within the DJI FPV and Vista high-frame-rate ecosystems. Utilizing an optimized 1/3-inch CMOS image sensor, this camera delivers a fluid digital transmission stream rendering 720p resolution at an ultra-high 120fps refresh rate in a native 4:3 display layout. Outfitted with an expansive 155-degree panoramic field of view and maintaining a low end-to-end latency floor of 28ms, the Wasp provides the sharp proximity tracking, multi-channel frequency separation, and rapid sensor response required by competitive drone racing and high-speed freestyle pilots.

Features

Optimized DJI Digital Ecosystem Alignment: Fully compatible with DJI FPV Goggles V2, Goggles 2, and Link/Vista video transmitter modules without requiring additional standalone radio receiver hardware.

Fluid 120fps High-Frame-Rate Pipeline: Transmits a rapid 120fps digital refresh stream, lowering real-time motion blur and smoothing out high-speed tracking environments.

Proximity-Optimized 155° Panoramic View: Equipped with an expansive wide-angle lens configuration that stretches spatial awareness across a 155-degree diagonal field of view, ideal for tight obstacle management.

Low-Latency 28ms Processing Floor: Features high-speed image processing subroutines to keep data throughput latency under a fixed 28ms threshold for immediate control stick feedback.

Eight-Channel Multi-Pilot Isolation: Supports up to 8 independent digital video channels simultaneously, allowing multiple pilots to race in the same space without video crossing or signal degradation.

Standardized 19mm Micro Form Factor: Enclosed in a compact 19mm × 19mm × 19mm square profile chassis weighing just 7.5 grams including its pre-installed 120mm heavy-shielded coaxial data lead.

Specifications

Brand: RunCam

Model Name: Link Wasp High-Frame-Rate Digital FPV Camera Matrix

Image Sensor Hardware: 1/3-Inch High-Performance CMOS Sensor Core

Digital Video Transmission Quality: 720p High-Definition @ 120 fps

Native Frame Aspect Ratio: 4:3 Standard Frame Layout

End-to-End Processing Latency: 28 ms Fixed Lower Floor Boundary

Shutter Mechanism Profile: Rolling Shutter Matrix

Simultaneous Signal Channel Maximum: 8 Independent Digital Channels

Primary Data Interconnect Cable: 120 mm Pre-Installed Coaxial Interface Ribbon

Physical Component Footprint: 19.0 mm × 19.0 mm × 19.0 mm (Micro Size Standard)

Physical Structural Net Mass: 7.5 g (Including integrated 120mm coaxial data lead)

Optical Field of View (FOV) Configurations

Diagonal Perspective Window: 155°

Horizontal Perspective Window: 125°

Vertical Perspective Window: 96°

Operational Instructions

Mechanical Mounting Integration: Place the 19mm micro camera housing between the structural carbon fiber side plates of your drone frame canopy. Secure the module using standard hardware casing screws, adjusting the vertical tilt angle to match your cruising velocity before final torque application.

Coaxial Interface Data Link: Route the pre-installed 120mm micro coaxial data cable away from high-power battery lines. Insert the coaxial terminal head straight into your Link/Vista digital video transmitter socket, lowering the primary mechanical retainer bracket plate to prevent impact disconnects.

Ecosystem Pairing and Binding: Power on your DJI FPV Goggles and the aircraft system. Press the dedicated bind buttons on the video transmitter module and the goggles simultaneously to initialize wireless link synchronization, confirming the digital 720p resolution initializes immediately.

Remote Controller Synchronization: Turn on your compatible DJI FPV Remote Controller. The integrated link protocol enables the transmitter to map control data over the existing digital connection path without requiring a separate standalone RC receiver module.

High-Frame Rate Configuration: Enter your FPV goggle display configuration menu and set the transmission parameter profile to High Frame Rate Mode to unlock the fluid 120fps pipeline and 28ms low-latency monitoring thresholds.

Notes

Delicate Coaxial Routing Precautions: The 120mm high-shielding coaxial cable carries high-frequency digital processing streams. Avoid pinching the cable under structural hardware plates or making sharp 90-degree creases, as internal core shielding fractures will lead to immediate digital pixel freeze, signal drops, or total video blackouts.

Lens Alignment and Impact Care: The ultra-wide 155-degree panoramic lens profile slightly extends past standard micro canopy protections. Always verify frame bracket standoffs extend clear of the glass optics or mount a clip-on protective lens element to absorb gravel and concrete impacts.

Avoid Mechanical Over-Tightening: When locking the side mounting screws into the camera's threaded metal framework, stop turning immediately once firm resistance is felt. Excessive torque can strip out the internal threads of the casing, resulting in severe flight vibration blurring and erratic footage.

Thermal Cross-Flow Air Management: Digital video transmission stacks running high-frame-rate profiles generate rapid localized heat build-up while sitting idle on the bench. Avoid leaving the flight battery connected for long configuration periods without active fan cooling to prevent automated thermal safety shutdowns.

Package

1 x RunCam Link Wasp Digital HD FPV Flight Camera Module (with integrated 120mm Coaxial Interconnect Cable)