Flywoo RunCam Link Wasp Digital HD FPV Camera System

The RunCam Link Wasp Digital HD FPV System is a high-performance, high-definition digital video transmission ecosystem engineered for seamless integration within the DJI FPV high-frame-rate ecosystem. Pairing the highly resilient RunCam Link video transmitter (VTX) with the ultra-smooth RunCam Wasp camera module, this integrated system delivers a fluid digital transmission stream rendering 720p resolution at an ultra-high 120fps refresh rate in a native 4:3 display layout. Outfitted with a broad 7.4V to 26.4V input voltage regulator, an expansive 155-degree panoramic field of view, and a premium omnidirectional Flywoo circular LHCP antenna, this bundle provides the sharp proximity tracking, extended range, and low end-to-end 28ms latency floor required by competitive drone racing and high-speed freestyle pilots.

Features

Optimized DJI Digital Ecosystem Alignment: Fully compatible with DJI FPV Goggles V2, Goggles 2, Goggles Integra, and the DJI FPV Remote Controller without requiring additional standalone radio receiver hardware.

Fluid 120fps High-Frame-Rate Pipeline: Transmits a rapid 120fps digital refresh stream, lowering real-time motion blur and smoothing out high-speed tracking environments.

Proximity-Optimized 155° Panoramic View: Equipped with an expansive wide-angle lens configuration that stretches spatial awareness across a 155-degree diagonal field of view, ideal for tight obstacle management.

Broad Input Voltage Architecture: Outfitted with an internal protection circuit that accepts direct power input from DC 7.4V up to 26.4V, facilitating direct compatibility with regulated flight controller pads or raw multi-S battery power up to a 6S LiPo rail.

Premium LHCP Signal Circle: Includes a high-efficiency Flywoo Circular Left-Hand Circularly Polarized (LHCP) antenna to maximize multi-path interference rejection and maintain a solid video link.

Standardized Form Factor Layouts: Combines a compact 29mm × 29mm square stackable VTX design with a standard 19mm micro camera profile for easy physical integration into modern drone frames.

Specifications

Brand: RunCam

Model Name: Link Wasp High-Frame-Rate Digital HD FPV System Bundle

RunCam Link VTX Specifications

Operating RF Frequency Band: 5.725 GHz – 5.850 GHz Wireless Band

Maximum Signal Range: < 4 km (FCC / SRRC Operating Profile Standards)

Input Voltage Operating Window: DC 7.4 V – 26.4 V (2S to 6S LiPo Battery Base Safe)

Average VTX Power Consumption: 4.0 W – 9.0 W Peak Demand

Physical Component Footprint: 29.0 mm × 29.0 mm × 13.0 mm

Physical Structural Net Mass: 19.5 g

RunCam Wasp Camera Specifications

Image Sensor Hardware: 1/3-Inch High-Performance CMOS Sensor Core

Native Video Transmission Quality: 720p High-Definition @ 120 fps

Native Frame Aspect Ratio: 4:3 Standard Frame Layout

Shutter Mechanism Profile: Rolling Shutter Matrix

Primary Data Interconnect Cable: 120 mm Pre-Installed Coaxial Interface Ribbon

Physical Component Footprint: 19.0 mm × 19.0 mm × 19.0 mm (Micro Size Standard)

Physical Structural Net Mass: 7.5 g (Including integrated 120mm coaxial data lead)

Optical Field of View (FOV) Configurations

Diagonal Perspective Window: 155°

Horizontal Perspective Window: 125°

Vertical Perspective Window: 96°

Operational Instructions

Mechanical Casing Integration: Position the 29mm × 29mm RunCam Link VTX mainboard within your drone frame's dedicated electronics bay, securing it using standard mounting brackets. Slide the 19mm micro camera housing between the structural side plates of your canopy, adjusting the vertical tilt angle before final torque application.

Wiring Harness Connections: Plug the included JST SH 1.0 6-pin silicone cable harness into the dedicated VTX port. Solder the opposite bare wire ends directly to your Flight Controller (FC) circuit pads: Red wire to a positive power pad (7.4V–26.4V safe), Black wire to a Ground (GND) pad, and the remaining UART lines to a free flight controller TX/RX telemetry pair.

RF Antenna Integration: Securely lock the provided Flywoo Circular LHCP antenna onto the VTX module's RF terminal socket. Use structural mounts to route the antenna lead away from carbon fiber frame edges and spinning propellers to maintain an optimal signal path.

Ecosystem Pairing and Binding: Power on your DJI FPV Goggles and link a flight pack to the drone. Press the dedicated bind buttons on the RunCam Link VTX module and the goggles simultaneously to initialize wireless link synchronization, confirming the digital 720p resolution initializes immediately.

High-Frame Rate Configuration: Enter your FPV goggle display configuration menu and set the transmission parameter profile to High Frame Rate Mode to unlock the fluid 120fps pipeline and 28ms low-latency monitoring thresholds.

Notes

RF Transmission Safety Policy: Never connect a flight battery to the RunCam Link VTX module without a 5.8G antenna clicked tightly onto its RF connector socket. Operating the VTX without an antenna prevents the transmitter from dissipating its RF energy, causing rapid heat buildup and permanent destruction of the primary amplification circuits.

Delicate Coaxial Routing Precautions: The 120mm high-shielding coaxial cable carries high-frequency digital processing streams between the camera and VTX. Avoid pinching the cable under structural hardware plates or making sharp 90-degree creases, as internal core shielding fractures will lead to immediate digital pixel freeze, signal drops, or total video blackouts.

VTX Thermal Heat Management Policy: High-definition digital video transmitters running high-frame-rate profiles generate rapid localized heat build-up while sitting idle on the bench without cross-flow ventilation. Avoid leaving the battery connected on the ground for extended setup periods; calibrate settings quickly or utilize a portable field fan to prevent automated thermal shutdown.

Avoid Mechanical Over-Tightening: When locking the side mounting screws into the camera's threaded metal framework, stop turning immediately once firm resistance is felt. Excessive torque can strip out the internal threads of the casing, resulting in severe flight vibration blurring and erratic footage.

Package

1 x RunCam Link Digital HD FPV Video Transmitter (VTX) Board Module

1 x RunCam Wasp Digital HD FPV Flight Camera (with integrated 120mm Coaxial Interconnect Cable)

1 x JST SH 1.0 6-Pin Flexible Silicone Connection Wire Loom

1 x Flywoo Circular 5.8G LHCP High-Efficiency Antenna Element

1 x Technical Hardware User Instruction Manual